Standard Pins and Wedges

STANDARD PIN Our round, tapered pins have a milled wedge slot. The shank is designed to eliminate pin sag and improve ease of stripping. Pins are made from steel and are heat-treated for long life.

STRAIGHT Wedges are used with pins to tighten adjoining concrete forms. Securing the tie and concrete form in place.

CURVEDWedges are used with pins to tighten adjoining concrete forms. Securing the tie and concrete form in place

Specialty Pins

FLATHEAD PIN The flathead pin is used when pinning through a single rail or when placing concrete against an existing wall. Also used in laydown applications, such as 36" x 96" panel, to pour a 36" tall concrete wall.

COMBINATION FILLER PIN WITH HEAD This pin passes completely through 2" aluminum fillers and connects adjoining panels with a wedge. To convert to either 1" or 1½" filler simply insert duplex nail in the appropriate hole. Combination with head - 1", 1½", 2"

STRAIGHT FILLER PIN. These pins pass through appropriate size fillers and are connected to adjoining panels with wedge.

PAX PIN Pax pin is slightly longer than our standard pin. Used with pax forms and special applications. CURVED PIN The curved pin is used in special corner and radius applications.

Top

Standard Wall Ties

WTF ties are manufactured to meet the requirements of today's various pouring methods. They are made of cold rolled steel. We continually perform quality control testing to ensure that all of our ties yield a minimum pull strength of 7,200#. TWO HOLE Single Rod Notch (SRN) Double Rod Notch (DRN) Triple Rod Notch (TRN) 4" Single Notch only 6" Single or Double Notch 8", 9", 10", 12" Available in Single, Double or Triple Notch Specify Nominal or Full Unlimited tie length available BREAKBACK TIES Breakback ties are vertical break ties designed to break back into the wall at specified dimensions. ¾" - Standard Breakback Other sizes available Any length Specify Nominal or Full.Breaking ties is accomplished by striking downward with hammer or utilizing the WTF Tie Breaker Bar

THREE HOLE Three Hole Tie: Used at top of concrete form with the aluminum waler brackets 4" - 6" Single Notch only 6" - 8" Single or Double Notch 8" - 10" Available in Single, Double or Triple Notch .Specify Nominal or Full Additional sizes - Single or Double Notch only Pin ONLY at shortest length (ex: DO NOT USE an 8" - 10" tie as a 10" tie) FOUR HOLE COMBINATION TIES Multi-dimensional ties are used when changing wall thickness. We recommend use of 50% more four hole ties in seam than would normally be used. Single Rod Notch - any length Specify Nominal or Full. Ties available in metric sizes. ROUND END TIES Available in 6" SRN, 8" TRN, 10" TRN Specify Nominal or Full

Top

Special Application Hardware

90° ANGLE CLIP Versatile 90° angle clip can be a substitute for full length outside corner angle to create an outside corner using fillers.

45° ANGLE CLIP Our 45° angle clip with rotating pins will affix two filler panels to form outside corner opposite a hinged inside corner.Can form 35° to 55°, depending upon the tightness of wedges.

ALUMINUM CAP CLIP The aluminum cap clip is designed to create a cap with 2"x12" lumber.

CAP/FILLER BRACKET Cap /filler brackets are used in conjunction with lumber to add height to a wall. The cap filler bracket pin is inserted into the top of the concrete form and the lumber is then nailed to the bracket. May also be used to construct job site plywood fillers when you need an extra filler or where you need to pass a pipe or other object through the concrete form

SADDLE BRACKET Unique brackets that allow another option for brickledge. The brackets pin onto the top rail of the lower form and allows the next stacked concrete forms to be inset 4 inches or 6 inches.

BRICKLEDGE BAR The Brickledge Bar permits another option for brickledge. The brackets pin onto the top rail of the lower form, then wood is nailed to under side of bracket. Upper panel is then placed on top of brickledge bar to create a 4" brickledge.

Top

DECK SLIDE CLAMP The deck slide clamp is used with our ledger system. Works with both the straight ledger and the crown mold ledger. The deck slide clamp pin is placed through the end bar hole into the ledger slot and then the slide is engaged

WINDOW CLAMP The window clamp is used at the top of the wall when a drop-in window buck is used. This clamp ensures that the window buck maintains a tight fit.

HAND PUNCH Our hand punch will add random pinholes with just a little punch. Holes can be added to side or end rails quickly in the field. Shipped with one 11/16" die set. Other die sets available Handles sold separately.

PARAPET BRACKET The Parapet Bracket is used in suspending the formwork on one side of the wall from the opposite side. This is commonly used in concrete pool systems.

PLYWOOD ADAPTER The plywood adapter allows the contractor to produce a filler using 1/2" or 5/8" plywood. Specify hole pattern and plywood thickness

SLIDE HAMMER Used to strip ledger and to break ties in crown mold ledger applications. The slide hammer is used to ease the stripping process of crown molding and wall panels under a deck. Also used to vertically break crown molding ties.

Top

Web design by Action Marketing
Copyright ©2003 WTF East. All Rights Reserved